2023年5月20日 · The problem is that even when i configure the windows server as an NTP server on the router, its still preferring to synchronize to its local NTP server on IP address 127.127.1.1, how can make the router to not use its local reference? below is the NTP configuration and output for some show commands: NBS-BT-DC-C4351-EDGE#sh run | sec ntp

2018年1月16日 · the Nexus stopped to send ntp requests from the Loopback interface0 (10.103.17.253) to the ntp server (10.92.1.4). The IP address of the ntp server (10.92.1.4) was configured on another switch (a C6509), neighbor of the Admin VDC of the Nexus. When I passed the command . no ntp peer 10.92.1.4 . on the C6509, the Nexus stopped to send ntp requests.

2013年12月4日 · So if your Gi0/0 has 172.16.7.2, use that IP address as the NTP server setting on the other devices. I suggest removing and not using the ntp source command. This command is not necessary nor useful in your current setup, neither on the NTP server, nor on NTP clients. Simply don't worry about it . Best regards, Peter

2010年1月15日 · Make sure that above mentioned NTP server(s) is reachable by pinging the server IP address(es). 4. Issue the command show ntp status on the server(s) to make sure that NTP server has synched itself. If it is not synched, verify the server NTP configuration. The show ntp status of the server should display a status of 'sync' before

2008年7月16日 · (cannot connect to NTP server) | Two Juniper Firewall Connected to Switch (can connect to NTP server) | 4500 Switch Connected to firewalls (can connect to NTP server) Show NTP config of 3640: ntp source FastEthernet2/0 . ntp server 69.25.233.209. Sh ntp associayion: address ref clock st when poll reach delay offset disp

2010年4月11日 · You get a bit better result if you use the continental zones (For example europe, north-america, oceania or asia.pool.ntp.org), and even better time if you use the country zone (like ch.pool.ntp.org in Switzerland) - for all these zones, you can again use the 0, 1 or 2 prefixes, like 0.ch.pool.ntp.org. Note, however, that the country zone might ...

2009年4月6日 · It is not recommended to use an HSRP virtual IP address as an NTP server address. Here is the reasoning: HSRP supplies a method of providing nonstop path redundancy . for the Internet Protocol (IP) by sharing protocol and Media Access . Control (MAC) addresses between redundant gateways.

2013年3月19日 · - Yes, hostname ntp.nic.cz is resolved to an ip address. Can you make a screenshot showing that? - No, see below. Do you have an active internet connection the switch is connecting to? - Yes. Can you try any other NTP server? - Yes. Only private range certain IP addresses are accepted (I have tested class C 192.168.x.x successfully)

2009年6月10日 · Also if you are using a Linux host as an NTP server and has hard-coded the stratum that it reports rather than let it calculate the stratum automatically. If it is a linux or unix box, the ntp server is configured by the file /etc/ntp.conf, and the "fudge" command is used to hard-code the stratum.

2012年7月2日 · The NTP configuration is very simple, no authentication or something, just "ntp server 10.x.x.x", that's all. "show ntp status" outputs on 2960: Cat2960#sh ntp status. Clock is unsynchronized, stratum 16, no reference clock. nominal freq is 119.2092 Hz, actual freq is 119.2082 Hz, precision is 2**17