DIY: VinceBar & Redish Motorsport Upper & Lower... - E46 …
2019年5月27日 · 20. Bolt down the vincebar to the rear section and the 2 gussets to the front section. Use the supplied drill bits (2 different sizes) to drill wherever the holes on the plates exist. The rear section holes need to be aprox. 15mm of depth, so the drill bit was marked. 21. Test fit that ALL rivets can sit in the final position. 22.
The Comprehensive E46 Brake Upgrade Guide
2016年7月11日 · Rear: (34 21 6 765 885) E46 330, E83 X3 2.5/3.0 (03-06), E83 X3 3.0 (06-10), Z4 3.0 Roadster/Coupe (04-08) Takeaway: First gen X3 is a great potential parts source. You can get front and rear calipers from a vehicle as new as 2010, providing a better likelihood of getting good, functional units.
Suspension Refresh Guide. Information w/ complete parts list.
2012年7月10日 · E46 Fanatics Forum is an independent BMW enthusiast website owned and operated by VerticalScope, Inc. Content on E46 Fanatics Forum is generated by its users. E46 Fanatics Forum is not in any way affiliated with Bayerische Motoren Werks AG VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada
So, you wanna service the rear trailing arm ... - E46 Fanatics Forum
2013年9月18日 · BMW has been using the rear trailing arm for decades. Its design coupled with careful suspension tuning has been one of key ingredients to BMW's dynamic driving qualities. The BMW rear trailing arm serves for the backbone of the rear suspension/wheel/wheel bearing/brakes and is designed to provide toe-out under heavy acceleration and toe-in ...
Rear Alignment Help, camber adjustment | E46 Fanatics Forum
2021年6月12日 · E46 Fanatics Forum is an independent BMW enthusiast website owned and operated by VerticalScope, Inc. Content on E46 Fanatics Forum is generated by its users. E46 Fanatics Forum is not in any way affiliated with Bayerische Motoren Werks AG VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada
How common are Subframe issues really? | E46 Fanatics Forum
2017年4月20日 · E46 Fanatics Forum is an independent BMW enthusiast website owned and operated by VerticalScope, Inc. Content on E46 Fanatics Forum is generated by its users. E46 Fanatics Forum is not in any way affiliated with Bayerische Motoren Werks AG VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada
Rear axle replacement - E46 Fanatics Forum
2014年1月7日 · E46 Fanatics Forum is an independent BMW enthusiast website owned and operated by VerticalScope, Inc. Content on E46 Fanatics Forum is generated by its users. E46 Fanatics Forum is not in any way affiliated with Bayerische Motoren Werks AG VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada
DIY: E46 Rear Wheel Bearing Replacement - Lots of pics!
2015年3月17日 · At 220k km my car developed a "wobling" sound coming from the rear end. I suspected rear bearings due to mileage so I gave it a go. Ordered 2 new SKF bearings, lock clip and the nut as a kit. The nut for the 320 is a 30mm one. Torque 250nm. Also ordered a set of genuine ATE handbrake spring kit to replace the rusted parts.
***BMW E46 Coupe Rear Deck Removal DIY*** - E46 Fanatics Forum
2007年10月26日 · BMW E46 Coupe Rear Deck Removal DIY Tools Needed: T-25 Torx Driver T-50 Torx Driver 8 mm Socket Flathead Screwdriver 1. Remove the lower seat bench. To remove you simply lift up and pull it out. You may need to be firm with your pull although it is only held on by a few clips. 2. Unbolt the large bolt holding on the seatbelts.
The best way to lift your E46 using a jack and jackstands
2012年10月16日 · The following photo is of an E46 M3 convertible. Same concept applies to this photo for your non-M cars. E46 M3s and earlier non-Ms have a front-central jacking point on the front subframe reinforcement. That can be used in a similar manner as the rear subframe lift point. Good luck and again, use common sense and safety!