Sizing 30-30 or 375 win brass to 38-55? - 24HOURCAMPFIRE
2010年4月2日 · Why?? For the reasons you stated in your earlier post. With properly sized cast bullets chambering is difficult to impossible when seated in either Win. or Starline 38-55 brass Solution is to go to the expense of enlarging your rifles chamber which are working well with jacketed bullets as is.
Tell me about forming 225 Win brass - 24HOURCAMPFIRE
2017年4月29日 · One could form .225's from .30/30 brass, but it would involve lathe work to reform the rim as well as forming work on the body of the case. Proper .225 brass can be found, and it is worth the trouble to look for it, compared to the hassle of forming it from .30/30 brass.
Making .22 HP brass - 24hourcampfire
2013年4月4日 · Done! Couldn't wait for the new die set to arrive, so necked the above-pictured 30-30 case that was reformed to 25-35 down to 22, and then seated a 60 gr Hornady .224" flat base using 22-250 FL die set. The case on the left is the reformed 30-30 brass, the right a …
Problem Necking .30-30 down to .219 Zipper Improved
2021年2月11日 · if you plan on using .30-30 brass, then a third set of dies would be helpful. Also, when going from .25-35 down to .22, don't try to run the ram all the way in. Run it in part way til you feel resistance, back it out, apply a bit more lube, I usually just redistribute what's already on the case, partially rotate the case in the shell holder and ...
Brand Preference - .30-30 Brass - 24HOURCAMPFIRE
2012年11月5日 · Regrettably but understandably, .30-30 brass just isn't made to the same tolerances as (for example) .308 brass. It is assumed that almost all of it will be fired and tossed by opening-day-only hunters. Let me hasten to say that it is all good brass, but it isn't match quality stuff or even close.
Using 30-30 brass for Contender 7-30 Waters - 24hourcampfire
2018年2月1日 · Max pressure for 30-30 is somewhere 40-42K PSI from what I can find online. 7-30 Waters is closer to 45-49K. Is there any issue of me using 30-30 brass in the 7-30 at >42K PSI? Is the 42K limit a function of the brass strength and/or action?
What are all the different methods to form .303 brass?
2012年1月25日 · Two good ways to make up .303 Savage brass: 1. First, get a set of .303 S dies from Lee. Resize and trim 30-30 brass. Cut a 4" long strip of masking tape about 1/4" wide and wrap around the base just ahead of the rim. This centralizes the smaller .30-30 base in the larger chamber. Load with bullet and fire form. Remove the tape.
OT: .30-30 to .25-35 dies - 24HOURCAMPFIRE
The only .25-35 brass I can find is Honrady, which I don't mind using, but I see conflicting information if it will work with a non-Hornady system. I have plenty of .30-30 brass and was wondering if the forming dies to convert are a viable option or if the Hornady brass will work with other dies. Input is welcome. Thanks.
What is the procedure for making .30 Herrett brass?
2013年7月9日 · Run .30-30 cases into sizer, to push back shoulder. At that point, a file trim die is convenient. Saw off excess case with a hacksaw, then file to length. Load a fireform load about 10-15% below max. When reloading fireformed cases, set sizer die to partial resize only, so brass stays snug in the chamber.
30 30 Win in a 303 Savage - 24HOURCAMPFIRE
2014年12月17日 · 2) The 30-30 brass is .02" longer, meaning that if it even chambers it very likely will be up against the rifling and could crimp the bullet in raising pressures. Even if resized, the .02" difference at the base would keep me from EVER using 30-30 brass in a 303 Savage rifle. It's just not worth the chance of serious case failures. 30-30: 303 ...