Toyota 4Runner 1984-1995 How to Replace Ball Joints - Yotatech
2016年1月20日 · Depending on the ball joint puller you have, you might have to remove the brake caliper and knuckle arm to gain adequate clearance as well. Use the ball joint puller to remove the upper, then the lower ball joints. Install the new upper as well as lower ball joints and torque to spec. Figure 6. Remove the upper ball joint. Figure 7. Remove the ...
Toyota 4Runner 1996-2002: How to Replace Lower Ball Joints
2016年2月4日 · Step 3 – Separate ball joint from knuckle. Now that the clearance is gained by removing the old outer tie rod end, we can begin to separate and remove the old ball joint. Remove the ball joint nut (24mm). Remove the four ball joint bolts (14mm). Use hammer with pickle fork or tie rod puller (if big enough) to separate ball joint from knuckle ...
Toyota 4Runner 1996-2002: Why is My Frame Squeaking?
2016年2月8日 · Commonly, those ball joints dry out and eventually crack if not greased quickly. If they need to be greased, make sure to use proper ball joint grease and a grease gun to penetrate the assembly. If not, visit your local dealer or repair shop to have them replaced. Figure 3. Ball joints hide behind a rubber boot. Figure 4. Replacement ball joint.
Toyota 4Runner 1984-1995: How to Replace Tie Rod Ends
2016年3月3日 · Figure 12. Put anti-seize or grease on threads. Screw the tie rod ends together to close to the same position, ball joint stud to ball joint stud, as the previous. Don’t tighten the clamps yet. Figure 13. Screw the inner and outer tie rod ends together. Also, the amount of thread inside the tie rod end adjusting sleeve should be approximately ...
Toyota Tundra 2000-Present: How to Replace Ball Joints
2016年1月28日 · Step 5 – Install ball joint. Installation is the reverse of removal: Press the new ball joint in place using the same tool. Righten the upper nut to 81 ft/lbs. Install the brake rotor, then install the brake caliper on top of it, and tighten its two bolts. Install all ABS attachments to control arm. Install the wheel and lower the truck ...
Grease Cap Cotter Pin Lock Cap Dust Boot Wire Snap Ring Upper Ball Joint Steering Knuckle Bearing Axle Hub Bearing Spacer Spacer Grease Cap Oil Seal ABS Speed Sensor Rotor Snap Ring Brake Dust Cover Oil Seal Non-reusable part w/o ABS 2WD 4WD w/ ABS 4WD N·m (kgf·cm, ft·lbf) : Specified torque 64 (650, 47) 105 (1,100, 80) 8.0 (82, 71 in.·lbf ...
What grease fitting for front u-joint? - YotaTech Forums
2011年9月21日 · I have not touched the grease fittings on the "propeller shaft" since I bought the truck a year and a half ago, and so I bought a needle adapter to reach the ridiculously deep set zerks on the driveshaft. I tried to pump while pushing the grease gun (lever style), and the needle bent (and leaked grease before it bent).
Toyota Tacoma: How to Replace Steering Rack Bushings
2016年2月2日 · Lightly lubricate the new bushing with silicone marine grease. Press both halves of the new bushing, and the bushing sleeve, into place with the large C-clamp. The large washer goes between the driver-side bushing and the frame crossmember. Passenger-side D-bushing: Spread the bushing where it is split and slip it off.
Toyota Tacoma and Tundra General Information and …
2016年1月27日 · Drain and refill your differential, transmission and transfer case fluids, flush your cooling system and inspect all ball joint covers and drive axle boots. The above-mentioned services should be carried out by a licensed professional, as many need to be performed in carefully-timed intervals.
Toyota 4Runner 1996-2002: How to Replace Shock Absorbers
2016年3月21日 · Slowly jack up the lower control arm to compress the suspension. Be sure the upper shock mount and spring are properly positioned while lifting. Re-attach the knuckle/hub to the lower ball joint using high-strength Threadlocker (red) on the bolts before tightening to approximately 165 ft/lbs. Figure 8. Lower ball joint bolt with Threadlocker ...