How to Change a CV Axle on an 01-04 ADD Tacoma
2008年12月15日 · Put the large nut onto the CV axle and tighten down. Place cotter pin lock onto the CV axle and then push cotter pin thru the hole to finish locking the CV in. Check the backside of the hub where the CV joint meets the hub to make sure it’s seated properly. There’s a gasket and lip there that should meet flush with the hub assembly. Step 12
How To Remove CV Axle+Replace Front Wheel Bearing 2nd Gen
2011年11月22日 · Disconnect upperball joint, tie rod end, lower shock bolt, and sway bar link. You will need to move the spindle to get the cv axle free you can see my cv boot torn in the back. the cv axle was 75 bucks i believe.(autozone) It beats 80 bucks at the dealer ship to replace JUST the cv boot. its just more work.
CV Axle Replacement ... express method!! - Tacoma World
2013年3月3日 · 2) Remove axle nut cover/cotter pin/axle nut. 2A) ADDED .. Remove sway bar end link from spindle, also brake line holder from spindle. 3) Undo lower ball joint (two 19mm bolts). 4) Once you have the ball joint undone, you can basically swing the whole caliper/rotor/spindle assembly out of the way, and push the axle out of the wheel hub.
Time to replace CV Axle, Need recommendations for replacement
2021年1月20日 · I have a torn CV axle boot, I am hearing popping sounds in the vicinity and need to replace it. I was quoted from Toyota that a single CV axle was $400+, yet AutoZone quoted me one of theirs for around $90 I have a non OEM one on now and it did last for many years. I am looking for a good value, possibly one I can re-grease too.
CV Axle Replacement - Tacoma World
2020年10月8日 · Joined: Jul 14, 2014 Member: #133888 Messages: 1,662 Gender: Male First Name: Jamin AZ Vehicle: 2011 DCLB 4x4 TRD Sport OME 885's paired to Bilstien 5100's, LR UCA's, OME Dakars w/ 5160's, Debadged Tailgate, TRD Stickers Removed, ARE Topper, Tailgate Theft Deterrent Mod, Mobtown Tailgate Skin, Light Bar in Hood Skewp, VIAIR OBA, …
How To: Remove and Replace CV Axles on 1st Gen A.D.D.
2010年12月5日 · Use pry bar (minimum of 18”, but 31” recommended) to pry CV axle from differential where the axle enters the differential. Step 10: Place CV axle in cleaning pan and use chisel and hammer to carefully beat factory boot clamps off of each boot. Step 11: Use utility knife to cut old boots off. Seriously, don’t use some crappy old, worn out ...
How to Change a CV Axle on an 01-04 ADD Tacoma
2008年12月15日 · I changed the CV axle on my 2001 Tacoma today and used this thread as a guide. It was very helpful, everything was pretty close to what was posted. One thing that wasn't the same tho was a metal piece at the upper end of the axle that goes up to the differential kinda like another seal or spacer.
Too much play in CV axle? - Tacoma World
2015年11月16日 · I then noticed the drivers side CV axle feels pretty loose on the transfer case side. Note* I did recently replace the drivers side front axle bearing but besides not getting the inner axle seal (the side on the inside of the axle bearing) lined up correctly at first no other issues occurred on that install.
2nd Gen CV Axle Removal Tips/Tricks/Advice - Tacoma World
2010年10月4日 · 3)Reinstalling the CV axle, make sure the C clip is oriented with the open side facing down. Make sure C clip is also centered on the axle, not cockeyed. Use thick grease to help hold the C clip in orientation. 4) Make sure axle is reinserted straight in, not off a little to work around hub, suspension, etc. IE have all shit out of your way!
2001 CV Axle replacement - Tacoma World
2012年3月1日 · The axle went in ok, but it is leaking a few drops after I put it all back in. Quite a bit of diff oil came out when I was changing it so I'm hoping that is the reason why and not that I used the metal seal (spacer).