motorcycle engine stand - Landracing.com
2010年5月29日 · I have the HF engine stand and made adaptors to fit my Suzuki engine mounts. It was merely a matter of cutting and drilling some angle iron. I don't know where the mounts are on your engine but I am sure you can make adaptors to fit the case. For the $39 (small one) or $79 (large one) you can't go wrong.
Motorcycle engine sizing - Landracing.com
2006年10月9日 · As for the non-vintage .020" over-size allowance, beats me. I guess it could be the way engine classes are defined. The motorcycle engine classes run along with the motorcycle manufacturers standard engine sizes.... IE 125cc, 250cc, 350cc, 500cc... they are all nominal engine sizes. Any bore clean-up would put them over the class limit.
Slick little motorcycle engine coupler - landracing.com
2006年10月17日 · the transworks mini-diff drive coupler is basically a 6-ball cv joint, made of heat treated 4140 chromoly steel, that attaches to the output shaft of a motorcycle engine in place of the stock sprocket. we manufacture the outer housing and other components, and then a modified sprocket is welded to the end of the.' housing.
When is a motorcycle engine, not a motorcycle engine
2009年7月20日 · The engine in question is the Hartley V8 made from two Hayabusa engines jioned with a common crank and crankcase. Does the fact that it uses Hayabusa parts, be good enough to satisfy the rule or would it be the fact that it is not made for any car or motorcycle, but could be used as a purpose biult motorcycle engine be good enough?
Airplane Engine on a motorcycle? - landracing.com
2022年2月28日 · Ride Motion in Australia says they are coming to Speedweek with a bike powered by an aircraft engine. At first, I said "no way" thinking that motorcycles engines were required on motorcycles. On reading the rule book however, I can't find that to be true. Anyone know differently? The AMA events like BMST DO require motorcycle engines.
Modified Vintage Gas Engine In Motorcycle Streamliner?
2009年3月11日 · Re: Modified Vintage Gas Engine In Motorcycle Streamliner? « Reply #29 on: March 11, 2009, 09:17:42 PM » Calkins How much hp does your motor make at the rear wheel willie buchta
Running a fuel pump on a carbureted motorcycle?
2018年4月20日 · Put soldering flux into one leg of a barbed brass Tee along with a big enough chunk of solder to fill that leg when you heat it with a propane torch. Stand that leg on a flat, steel surface when you melt the solder. It won't stick to the steel and won't run out. JB Weld works fine too. Drill a 1/16th hole in the solder.
Bonneville Motorcycle Speed Trials 2024 - landracing.com
2024年10月13日 · I brought a 1970 Yamaha R-5 350 fitted with a TZ-350 engine. The engine is basically an early TZ-350 fitted with G model 6 transfer port cyclinders and an E model head fitted with removeable combustion chambers. The carbs are 38 mm round slide power jet Mikuni items. The pipes are British Swabricks and the ignition is PVL analog.
J and K engine class lakester - Landracing.com
2023年6月10日 · I don't really think, from a practical point of view, that using anything except a late model 4 cylinder motorcycle engine is an option if your target is a record. They come with a state of the art design, a close ratio multi speed transmission and easy adaption using the original chain drive design which is pretty efficient and straight forward.
LTA Motorcycle Class Additions - landracing.com
2011年11月20日 · Any 4-stroke motorcycle engine with 1 or 2 cylinders. Unlimited in design and modification. Pushrod and OHC engines with cylinder angles of 0 – 180 degrees allowed. Subject to the same limitations as (G) and (F) respectively. …